Bob Smith Industries CA Adhesives - DeBonders

_____ Updated 3 08 08_____

Loctite Thread Lock Adhesives

JB Weld

Bob Smith Industries CA Adhesives
Accelerators & Debonders

BSI Rubber Tough CA - 1/2 oz.
IC-2000™ is a rubber-toughened cyanoacrylate that forms superior shock resistant bonds on non-porous surfaces. The black colored CA has added flexibility for the bonding of metals, fiberglass, rubber, carbon-fiber and other advanced materials. For model use, IC-2000™ is ideal for the bonding of bulkheads, formers and servo rails to the inside of fiberglass hulls and fuselages. Setup time is 20-40 seconds, which can be accelerated with INSTA-SET™. When cured, IC-2000™ is pliable enough to be carved with a hobby knife. IC-2000™ is the best adhesive for R/C car tires.

Qty

Part # 117

Rubber Tough CA - 1/2 oz.

$5.39

In Stock

BSI Super Thin CA - 1/2 oz.
INSTA-CURE™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond.

Qty

Part # 101

BSI Super Thin CA - 1/2 oz.

$3.29

In Stock

BSI Gap Filling Medium CA - 1/2 oz.
INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, dont spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out.

Qty

Part # 106

BSI Thin - Gap Filling Medium CA - 1/2 oz.

$2.99

In Stock

BSI Thick CA - 1/2 oz.
SUPER-GOLD and SUPER-GOLD+ are our odorless INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLDs do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARFs. They will not fog clear plastic. SUPER-GOLD+ is ideal for attaching clear canopies in plastic model kits; however, MAXI-CURE is still recommended for assembling the rest of plastic kits. Wood can be bonded to white foam with SUPER-GOLD + in less than fifteen seconds. For bonding foam to foam, spray a very light fog of INSTA-SET to one piece and apply SUPER-GOLD+ to the other before joining. Excess INSTA-SET may create too much heat, which can melt the foam. Both SUPER-GOLDs cure to a more flexible consistency for better shock absorbtion. Whenever a large amount of CA is to be used in such applications as saturating fiberglass or Kevlar, SUPER-GOLD eliminates the irritating fumes from the evaporating monomer that make repeated use of CA unpleasant at times.

Qty

Part # 126

BSI Thick - Super Gold
CA 1/2 oz.

$6.99

In Stock

BSI Debonder
UN-CURE debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water.

Qty

Part # 161

BSI Un-Cure Debonder
1 oz.

$2.99

In Stock

BSI Insta - Set CA Accelerator
INSTA-SET is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET significantly enhances a joints strength. For difficult to bond materials, INSTA-SET can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.

Qty

Part # 151

BSI Accelerator
2 oz.

$4.99

In Stock


	Home \| Phone Contact \| E Mail Us \| >> New Stuff << \| Shipping Rates \| Sales Policies/Returns \| View Cart


	DeeTee Enterprises RC Hobbies \| P.O. Box 40667 \| Eugene, Oregon \| 97404-0108

New Orders/Inquiries/Tech Support
Dennis 1 541 302 0806
New Orders/Inquiries/Tech Support
Jay 1 541 345 1070